Power Generation I&C Maintenance Technician

Module ID 40103-07; from Industrial Maintenance E&I Technician Level One: Covers hardware and systems used in industrial maintenance. Describes anchors and supports, their applications, and how to install them safely.

Module ID 40104-07; from Industrial Maintenance E&I Technician Level One: Explains the safety requirements for oxyfuel cutting. Identifies oxyfuel cutting equipment and provides instructions for setting up, lighting, and using the equipment. Explains how to perform straight line cutting, piercing, beveling, washing, and gouging.

Module ID 40105-07; from Industrial Maintenance E&I Technician Level One: Introduces gaskets and gasket material, packing and packing material, and types of O-ring material. Explains the use of gaskets, packing, and O-rings, and how to fabricate a gasket.

Module ID 40106-07; from Industrial Maintenance E&I Technician Level One: Explains how to use ratios and proportions, solve basic algebra, area, volume, and circumference problems, and solve for right triangles using the Pythagorean theorem.

Module ID 40107-07; from Industrial Maintenance E&I Technician Level One: Introduces plot plans, structural drawings, elevation drawings, as-built drawings, equipment arrangement drawings, P&IDs, isometric drawings, basic circuit diagrams, and detail sheets.

Module ID 40108-07; from Industrial Maintenance E&I Technician Level One: Explains centrifugal, rotary, reciprocating, metering, and vacuum pump operation and installation methods, as well as types of drivers. Describes net positive suction head and cavitation.

Module ID 40109-07; from Industrial Maintenance E&I Technician Level One: Identifies different types of valves and describes their installation, storage, and handling.

Module ID 40110-07; from Industrial Maintenance E&I Technician Level One: Introduces test equipment for industrial maintenance, including tachometers, pyrometers, strobe meters, voltage testers, and automated diagnostic tools.

Module ID 40111-07; from Industrial Maintenance E&I Technician Level One: Introduces the equipment and techniques of
material handling, and describes the procedures for rigging and communicating with riggers.

Module ID 40112-07; from Industrial Maintenance E&I Technician Level One: Introduces the safety procedures and methods of operation for motorized support equipment, including forklifts, manlifts, compressors, and generators.

Module ID 40113-07; from Industrial Maintenance E&I Technician Level One: Explains lubrication safety, storage, and classifications. Also explains selecting lubricants, additives, lubrication equipment, and lubricating charts.

Module ID 29107-09; from Welding Level One, Fourth Edition: Describes SMAW welding and welding safety. Explains how to connect welding current and set up arc welding equipment. Also explains how to use tools for cleaning welds.

Module ID 40303-09; from Industrial Maintenance E&I Technician Level Three: Explains how to read and interpret piping and instrumentation drawings, loop sheets, flow diagrams, isometrics, and orthographics, in order to identify types of instrumentation and the specifications for installation.

Module ID 40205-08; from Industrial Maintenance E&I Technician Level Two: Focuses on proper selection, inspection, and use of common electrical and instrumentation test equipment, including voltage testers, clamp-on ammeters, ohmmeters, multimeters, phase/motor rotation testers, data recording equipment, field communicators, pressure testers, and dead weight testers. Also covers safety precautions and meter category ratings.

Module ID 40201-08; from Industrial Maintenance E&I Technician Level Two: Covers safety rules and regulations for electrical workers, precautions for electrical hazards on the job, and the OSHA-mandated lockout/tagout procedure.

Module ID 26501-09; from Electrical, First Edition: Introduces electrical hazards in the workplace and describes how to avoid them. Explains how to analyze and document shock and arc flash hazards, and how to plan and conduct work around them. Includes examples of how to complete an energized electrical work permit, and how to select the specialized personal protective equipment required for electrical work.

Module ID 40212-08; from Industrial Maintenance E&I Technician Level Two: Focuses on the types and applications of conductors and electrical cabling and covers proper wiring techniques. Stresses the applicable NEC® requirements.

Module ID 40213-08; from Industrial Maintenance E&I Technician Level Two: Describes methods of terminating and splicing conductors of all types and sizes, including preparing and taping conductors.

Module ID 40304-09; from Industrial Maintenance E&I Technician Level Three: Describes selecting, sizing, and installing motor controllers. Also covers control circuit pilot devices and basic
relay logic.

Module ID 40202-08; from Industrial Maintenance E&I Technician Level Two: Provides a road map for using the NEC®. Introduces the layout and types of information found within the code book. Allows trainees to practice finding information using an easy-to- follow procedure.

Module ID 40203-08; from Industrial Maintenance E&I Technician Level Two: Introduces electrical concepts used in Ohm’s law as applied to DC series circuits. Includes atomic theory, electromotive force, resistance, and electric power equations. Introduces series, parallel, and series-parallel circuits. Covers resistive circuits, Kirchhoff’s voltage and current laws, and circuit analysis.

Module ID 40311-09; from Industrial Maintenance E&I Technician Level Three: Introduces hydraulic principles and fluids, functions and controls of system devices, hydraulic symbols, and drawings. Covers safety considerations for hydraulic systems, as well as troubleshooting.

Module ID 40312-09; from Industrial Maintenance E&I Technician Level Three: Describes principles of atmospheric and compressed air gases, and how compressors transmit and treat compressed (pneumatic) air. Covers pneumatic system symbols, drawings, and system safety. Addresses the functions and control of pneumatic system components and provides guidelines for troubleshooting.

Module ID 40409-09; from Industrial Maintenance E&I Technician Level Four: Introduces the application of PLCs in industrial process control, as well as the binary numbering system used in computer- based control. Covers components of PLCs, including power supplies, I/O modules, processor modules, types of communication bus, and memory.

Module ID 40207-08; from Industrial Maintenance E&I Technician Level Two: Covers measurement of mass, weight, pressure, temperature, and flow, conversion of units, and their application to industrial maintenance.

Module ID 12213-03; from Instrumentation Level Two, Second Edition: Covers selection and mounting of instruments at locations other than panels, including stand mounting, in-line mounting, structure mounting, strap mounting, and insertion mounting.

Module ID 40206-08; from Industrial Maintenance E&I Technician Level Two: Presents devices used to measure flow, pressure, level, and temperature, along with their principles of operation.

Module ID 40211-08; from Industrial Maintenance E&I Technician Level Two: Introduces instrument symbols, abbreviations, and drawings and documents, including instrument indexes, installation detail drawings, location drawings, and control loops.

Module ID 12104-01; from Instrumentation Level One, Second Edition: Covers basic electrical concepts and terms, DC circuit calculations, electrical measuring instruments, and electrical wiring.

Module ID 12208-03; from Instrumentation Level Two, Second Edition: Presents the principles of operation and applications of various relays and timers. Also reviews the selection process for these devices.

Module ID 12209-03; from Instrumentation Level Two, Second Edition: Covers the principles of operation and applications of switches and photoelectric devices in the instrumentation environment.

Module ID 12306-03; from Instrumentation Level Three, Second Edition: Teaches the basic concepts of grounding and shielding, including wire and cable identification. Defines various types of noise that can be induced into instrumentation wiring and describes the methods used to reduce or eliminate it.

Module ID 40209-08; from Industrial Maintenance E&I Technician Level Two: Introduces a variety of tubing, tubing materials, tools, and work practices. Covers proper storage and handling, cutting, deburring, reaming, bending, and flaring of tubing.

Module ID 40210-08; from Industrial Maintenance E&I Technician Level Two: Presents safe methods for cleaning, purging, blowing down, pressure testing, and leak testing tubing, piping, and hoses used in industrial maintenance.

Module ID 40309-09; from Industrial Maintenance E&I Technician Level Three: Introduces piping and tubing layout procedures. Explains the steps for creating a hand-sketched isometric drawing that can be applied to a piping and tubing installation. Introduces methods and procedures used to measure, cut, bend, and support piping and tubing.

Module ID 40302-09; from Industrial Maintenance E&I Technician Level Three: Introduces the principles of electronics and semiconductor theory, components, and applications.

Module ID 12212-03; from Instrumentation Level Two, Second Edition: Explains the selection of instruments to be panel-mounted, locating the instruments using drawings, and procedures for installing the instruments in the panels.

Module ID 12408-03; from Instrumentation Level Four, Second Edition: Defines various types of analyzers and their applications in industrial process control. Includes a discussion of analyzers that measure or monitor variables such as density, specific gravity, viscosity, turbidity, flashpoint, oxidation-reduction potential (ORP), pH, conductivity of a liquid, oxygen, carbon monoxide, carbon dioxide, hydrogen sulfide, total hydrocarbon content (THC), and particulates in a clean room. Also defines chromatography and ultraviolet and infrared analyzers.

Module ID 40402-09; from Industrial Maintenance E&I Technician Level Four: Discusses sensing and transmitting devices used in an instrumentation loop, along with the process variables measured by the detectors or sensors. Gives examples of technical manuals and specification sheets. Explains how control devices are selected, and how to draw basic control loop diagrams that include a measuring element, a transducer, and a transmitter.